NOOELEC NESDR SMART SETUP DRIVERS
NOOELEC NESDR SMART SETUP FULL
NOOELEC NESDR SMART SETUP SOFTWARE
NOOELEC NESDR SMART SETUP SERIES
NOOELEC NESDR SMART SETUP TV

Update: The USRADIOGUY GOES Satellite Imagery ReceptionВ is a great place for info, that would have been quite helpful had I known about it when I started.

NOOELEC NESDR SMART SETUP SOFTWARE

The hardware and software requirements for successful GOES-13 decoding are completely different from GOES-16/17 and all other L-Band geostationary weather satellites, do not expect the same setup that works for LRIT/HRIT to work with GOES-13 See also the reddit PSA PSA: What you need to know about GOES-13: This was somewhat of a gamble, as I bought mine before any of the reviews on Amazon. I was inspired to buy the Nooelec kit on AmazonВ after reading about it on the RTL SDR blog, in particular the quite excellent online tutorial on GOES 16/17 Weather Satellite Reception. I first received their NESDR Smart RTL-SDRВ as a birthday present several years ago, and really enjoyed setting up OpenWRT on EA3500 with RTL-SDR Stream. This is certainly not my first SDR product from Nooelec.

NOOELEC NESDR SMART SETUP TV

I've never even owned a TV satellite dish. 2m (6.I've been wanting to learn about satellite reception and SDR signal processing for quite some time.Wide base with super-strong magnet within base for easy mounting.The form factor re-design allowed us to move to the more universal SMA antenna input.There is no need to remove the enclosure to run multiple SDRs beside one another! This ensures they can be used side by side in any USB-compliant device, including tightly-spaced embedded devices.

NOOELEC NESDR SMART SETUP SERIES

The NESDR SMArt series of SDRs were designed to minimize annoying USB port occlusion.

The changes were first simulated, and then field-tested with a Flir E8.

The result is much lower board-level temperaturesвЂ“increasing stability, improving sensitivity and ensuring maximum frequency range capability.

Power consumption has been reduced by an average of 10mA, which means less heat is generated compared to other designs.

2 pieces of silicone thermal padВ spread the rest of the heat away from the device hot spots.

A custom heatsink is affixed to the primary PCB with 3M thermal adhesive, to wick heat away from the circuit board and towards the enclosure.

The new PCB design of the NESDR SMArTee results in temperatures an average of 10вњ¬ lower than the NESDR SMArt (v1-v3)!.

NOTE: Do NOT permanently short the antenna port! The protection circuitry is designed for periodic and inadvertent short circuits only!.

Protection circuitry is includedВ to prevent permanent damage from accidental short-circuits.

Bias-tee can provide up to 250mAВ to your active circuitry without exceeding USB power limitations (500mA).

Regulator adds less than 10 ВµVRMS of noise.

NOOELEC NESDR SMART SETUP DRIVERS

No need to mess around with software or drivers to enable your bias tee!

Bias-tee does NOT need to be enabled with hardware or software hacks.

RF-suitable 4.5V regulator provides DC output to power your active electronics.

NOOELEC NESDR SMART SETUP FULL

Full ESD circuitry on both the antenna input and the USB port provides protection for your investment, and peace of mind that your SDR will work when you need it most.

Lower board-level temperaturesВ further improves the SDR noise floor.

The included aluminum enclosureВ ensures stray EMI stays where it belongsвЂ“away from the sensitive RF circuitry.

A quality shielded inductor was used in the power supply to improve EMI rejection.

That is at least 10x lower than other designs!

In the quest for lower noise, the power supply section utilizes an RF-suitable voltage regulatorВ with under 10 ВµVRMS of noise.

The NESDR SMArTee contains the same ultra-low phase noise 0.5PPM TCXOВ used in our much smaller Nano 3 (TCXO specifications below), ensuring ultimate tuning stability in nearly any environment.

433MHz (ISM) antenna mast (fixed frequency).

Telescopic antenna mast (variable frequency).

NESDR SMArTee SDR w/ brushed aluminum enclosure.

The NESDR SMArTee v2 is fully equivalent in terms of function, noise performance and sensitivity to NESDR SMArt v4, but with an added DC power output (4.5V 250mA max) on the antenna port to power active electronics like our SAWbird series of LNA modules The result? A reduction in the noise floor of an AVERAGE of ~3dB over the already high-performing NESDR SMArt (v1-v3)вЂ“with an additional always-on bias-tee featureвЂ“all in the same fantastic form factor! We designed this SDR from the ground up in order to develop the best low-cost SDR in existence. This premium RTL-SDR was designed, developed and fabricated by Nooelec in the USA and Canada, and comes complete with a full 2-year product warranty.

Nooelec nesdr smart setup